- #Wrx best boost gauge how to
- #Wrx best boost gauge install
- #Wrx best boost gauge drivers
- #Wrx best boost gauge manual
Revel VLS II Analog Gauges are the latest addition to the Revel line of gauges. Choose from Autometer, Greddy, Innov Evokiller. The stock boost gauges, on both of my WRX & STi, measure in MPa. 7 pounds of boost, it’s been retuned to 305 horsepower, a jump of 12, and 290 pound-feet of torque. Start the engine and check for any leaks in the system. Leave about 1/2-inch of line extending out from the connector and screw it onto the fitting in the intake air-horn. Thread the NPT fitting onto the end of the boost line. Tighten it, using a wrench.Ĭut the boost hose to the desired length with a pair of scissors.
Thread the NPT fitting that came with the boost gauge into the hole. This will provide threads in the hole for the NPT fitting to connect. Rotate the tapping tool into the hole while pressing it with your hand.
#Wrx best boost gauge install
Install the 1/8-inch NPT tap into the tapping tool hardware. Keep the drill straight to ensure that a quality hole is made. The intake air-horn is on the rear of the engine cover (which has "Powerstroke" stamped on it) - it is a cylindrical metal section that connects the large air hose to the turbocharger.ĭrill a 5/16-inch hole into the top of the intake air-horn, using a metal drill bit and a power drill. Run the line to the intake air-horn, inside the engine compartment. The hole is located on the driver's side of the engine, under the steering wheel. Route the boost line through the hole in the firewall. Thread the connector onto the fitting on the gauge and tighten the nut with a wrench. Leave about 1/2-inch of the line extending past the connector. Slide the connector onto the end of the boost line. Attach the red wire to the fuse connector marked "Headlamp." Attach the black wire to the ground screw, using a screwdriver (the ground screw is green). Route the wiring harness from the gauge to the fuse panel inside your vehicle. Mount the gauge pod onto the dashboard of your Powerstroke-equipped vehicle, using the screws provided and a screwdriver.
#Wrx best boost gauge manual
Refer to the owner's manual for proper bracket installation. Different gauge manufacturers use different methods of securing the gauge. Place the gauge mounting bracket onto the back side of the gauge to hold it in position in the pod. Slide the boost gauge into the front of the gauge pod until the gauge stops from going any further.
#Wrx best boost gauge how to
How to Install a Boost Gauge to a 7.3 Powerstroke
Turn on the headlights and confirm that the light on the gauge illuminates properly. Verify that the gauge pressure increases when the throttle is depressed. Start the engine and check for any leaks. Thread the connector into the hole in the intake manifold. Slide the connector that came with the kit onto the end of the 1/8-inch hose. Reinstall the intake manifold onto the engine. Tap the hole for threads using a 1/8-inch NPT tapping tool. The location of the hole does not specifically matter however, it is best to place the hole on the flat section because it will be easier to drill straight. Remove the intake manifold and place it on a work surface.ĭrill a 5/16-inch hole into the intake manifold. Remove the intake manifold by loosening and removing the bolts that secure the intake manifold to the engine with a wrench.
#Wrx best boost gauge drivers
The large hose from the turbocharger connects to the intake manifold on the drivers side of the engine. The intake manifold is the metal intake bracket mounted on the top side of the engine. Route the 1/8-inch hose to the intake manifold. Route the black wire from the gauge to the battery in the engine compartment. Route the 1/8-inch hose and the black wire from the gauge through the hole in the firewall which is located on the drivers side of the vehicle. Attach the fitting to the connector on the back side of the gauge. Thread the NPT fitting that came with the kit onto the 1/-8-inch hose. Attach the wire to the fuse that is marked "headlamps." This will allow the light on the gauge to come on only when the headlights are turned on. Route the red wire from the gauge into the fuse box. If the pod requires mounting, mount the pod with a screwdriver using the screws that came with the pod. How to Install a Boost Gauge in a Dodge Cummins
0 kommentar(er)
